banana pi(BPI-M1)定制为openwrt系统的路由器
纠错
01 Mar 2016
1. 定制路由器目标介绍
定制目标如下图
2. 定制过程
2.1 增加USB RNDIS实现共享安卓手机上网
首先, 版本编译配置
1 2 3 4 5 6 7 8 9 10 11 | make menuconfig # 进行如下配置 Kernel modules ---> USB Support ---> <*> kmod-usb-net Kernel modules ---> USB Support ---> -*- kmod-usb-net-cdc-ether Kernel modules ---> USB Support ---> <*> kmod-usb-net-rndis Utilities ---> <*> usbutils Base system ---> <*> udev # 保存配置并编译运行 make V=99 |
其次, 进行网络配置使能USB RNDIS共享上网
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 | root@BananaPi:/# cat /etc/config/network
config interface 'loopback'
option ifname 'lo'
option proto 'static'
option ipaddr '127.0.0.1'
option netmask '255.0.0.0'
config globals 'globals'
option ula_prefix 'fdb6:87de:16ab::/48'
config interface 'wan'
option ifname 'usb0'
option proto 'dhcp'
config interface 'lan'
option ifname 'eth0'
option force_link '1'
option type 'bridge'
option proto 'static'
option ipaddr '192.168.1.1'
option netmask '255.255.255.0'
option ip6assign '60'
root@BananaPi:/#
# 插上三星手机并开启USB网络共享功能
[ 131.574646] usb 2-1: new high-speed USB device number 2 usim
[ 132.044644] usb 4-1: new full-speed USB device number 2 using ohci-platform
[ 132.257665] usb 4-1: not running at top speed; connect to a high speed hub
[ 132.279670] usb 4-1: New USB device found, idVendor=04e8, idProduct=6860
[ 132.286397] usb 4-1: New USB device strings: Mfr=2, Product=3, SerialNumber=4
[ 132.293527] usb 4-1: Product: SCH-N719
[ 132.297296] usb 4-1: Manufacturer: samsung
[ 132.301395] usb 4-1: SerialNumber: xxx
[ 135.165451] usb 4-1: USB disconnect, device number 2
[ 135.414652] usb 2-1: new high-speed USB device number 3 using ehci-platform
[ 135.884642] usb 4-1: new full-speed USB device number 3 using ohci-platform
[ 136.097677] usb 4-1: not running at top speed; connect to a high speed hub
[ 136.119680] usb 4-1: New USB device found, idVendor=04e8, idProduct=6860
[ 136.126411] usb 4-1: New USB device strings: Mfr=2, Product=3, SerialNumber=4
[ 136.133539] usb 4-1: Product: SCH-N719
[ 136.137419] usb 4-1: Manufacturer: samsung
[ 136.141514] usb 4-1: SerialNumber: xxx
[ 145.214372] usb 4-1: USB disconnect, device number 3
[ 145.504650] usb 2-1: new high-speed USB device number 4 using ehci-platform
[ 146.044645] usb 2-1: device not accepting address 4, error -71
[ 146.504638] usb 4-1: new full-speed USB device number 4 using ohci-platform
[ 146.717683] usb 4-1: not running at top speed; connect to a high speed hub
[ 146.735676] usb 4-1: New USB device found, idVendor=04e8, idProduct=6863
[ 146.742385] usb 4-1: New USB device strings: Mfr=2, Product=3, SerialNumber=4
[ 146.749548] usb 4-1: Product: SCH-N719
[ 146.753298] usb 4-1: Manufacturer: samsung
[ 146.757415] usb 4-1: SerialNumber: xxx
[ 146.784775] rndis_host 4-1:1.0 usb0: register 'rndis_host' at usb-1c1c400.us6
root@BananaPi:/# ifconfig
br-lan Link encap:Ethernet HWaddr 02:88:07:C1:62:AA
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fdb6:87de:16ab::1/60 Scope:Global
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
eth0 Link encap:Ethernet HWaddr 02:88:07:C1:62:AA
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:920 (920.0 B)
Interrupt:117
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:1552 errors:0 dropped:0 overruns:0 frame:0
TX packets:1552 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:94728 (92.5 KiB) TX bytes:94728 (92.5 KiB)
usb0 Link encap:Ethernet HWaddr 02:01:67:31:62:36
inet addr:192.168.42.220 Bcast:192.168.42.255 Mask:255.255.255.0
inet6 addr: fe80::1:67ff:fe31:6236/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:387 errors:0 dropped:0 overruns:0 frame:0
TX packets:378 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:25412 (24.8 KiB) TX bytes:45056 (44.0 KiB)
root@BananaPi:/# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
default 192.168.42.129 0.0.0.0 UG 0 0 0 usb0
192.168.1.0 * 255.255.255.0 U 0 0 0 br-lan
192.168.42.0 * 255.255.255.0 U 0 0 0 usb0
192.168.42.129 * 255.255.255.255 UH 0 0 0 usb0
# ping test ok
root@BananaPi:/# ping www.baidu.com
PING www.baidu.com (14.215.177.37): 56 data bytes
64 bytes from 14.215.177.37: seq=0 ttl=50 time=75.508 ms
64 bytes from 14.215.177.37: seq=1 ttl=50 time=72.230 ms
64 bytes from 14.215.177.37: seq=2 ttl=50 time=68.092 ms
^C
--- www.baidu.com ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 68.092/71.943/75.508 ms
root@BananaPi:/#
|
2.2 增加USB WIFI AP
笔者手上有一个TP-LINK TL-WN823N 1.0的usb wifi网卡, 直接插到系统中, 不能正常识别为USB WIFI, 打印如下:
1 2 3 4 5 6 7 | [ 1850.481766] usb 1-1: USB disconnect, device number 2 [ 1956.593682] usb 1-1: new high-speed USB device number 3 using ehci-platform [ 1956.745456] usb 1-1: New USB device found, idVendor=0bda, idProduct=8178 [ 1956.752164] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 1956.759333] usb 1-1: Product: USB WLAN [ 1956.763091] usb 1-1: Manufacturer: 802.11n [ 1956.767217] usb 1-1: SerialNumber: 00e04c000001 |
首先, 需要增加USB WIFI驱动和hostapd工具软件.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 | make menuconfig # 配置 Kernel modules ---> USB Support ---> <*> kmod-usb-ohci Kernel modules ---> USB Support ---> <*> kmod-usb-uhci Kernel modules ---> USB Support ---> <*> kmod-usb2 Kernel modules ---> Wireless Drivers ---> -*- kmod-cfg80211 Kernel modules ---> Wireless Drivers ---> <*> kmod-lib80211 Kernel modules ---> Wireless Drivers ---> <*> kmod-mac80211 Kernel modules ---> Wireless Drivers ---> <*> kmod-rtl8192cu Network ---> <*> hostapd Network ---> -*- hostapd-common Network ---> <*> hostapd-utils |
其次, 编译并烧结新固件.
1 2 3 4 | make V=99 # 烧结 BPI-OpenWRT/bin/sunxi# dd bs=4M if=openwrt-sunxi-BPI-M1-sdcard-vfat-ext4.img of=/dev/sdb |
然后, TL-WN823N插入单板, 上电启动.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 | # 启动信息, 如下反应显示识别了USB WIFI
[ 1.694721] usb 2-1: new high-speed USB device number 2 using ehci-platform
[ 1.846597] usb 2-1: New USB device found, idVendor=0bda, idProduct=8178
[ 1.853307] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.860492] usb 2-1: Product: USB WLAN
[ 1.864245] usb 2-1: Manufacturer: 802.11n
[ 1.868404] usb 2-1: SerialNumber: 00e04c000001
[ 1.884479] init: Console is alive
[ 1.888198] init: - watchdog -
[ 2.892113] init: - preinit -
Detected bpi-m1 // BPI M1
[ 3.002254] random: mktemp urandom read with 5 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.071012] mount_root: mounting /dev/root
[ 6.080777] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 6.091685] procd: - early -
[ 6.094782] procd: - watchdog -
[ 6.900228] procd: - ubus -
[ 7.915836] procd: - init -
Please press Enter to activate this console.
[ 8.625908] NET: Registered protocol family 10
[ 8.637094] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 8.650913] Netfilter messages via NETLINK v0.30.
[ 8.657082] ip_set: protocol 6
[ 8.682995] sunxi-rtc 1c20d00.rtc: rtc core: registered rtc-sunxi as rtc0
[ 8.690624] sunxi-rtc 1c20d00.rtc: RTC enabled
[ 8.756566] Loading modules backported from Linux version master-2015-03-09-5
[ 8.764501] Backport generated by backports.git backports-20150129-0-gdd4a670
[ 8.773712] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 8.782877] lib80211: common routines for IEEE802.11 drivers
[ 8.793851] nf_conntrack version 0.5.0 (16024 buckets, 64096 max)
[ 8.931123] xt_time: kernel timezone is -0000
[ 8.936902] usbcore: registered new interface driver cdc_ether
[ 8.958896] cfg80211: Calling CRDA to update world regulatory domain
[ 8.965660] cfg80211: World regulatory domain updated:
[ 8.972038] cfg80211: DFS Master region: unset
[ 8.976523] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_ga)
[ 8.986446] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 )
[ 8.994484] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 )
[ 9.002634] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 )
[ 9.010772] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 )
[ 9.018924] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz A)
[ 9.028540] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000)
[ 9.036714] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 )
[ 9.044827] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0)
[ 9.090765] PPP generic driver version 2.4.2
[ 9.096431] NET: Registered protocol family 24
[ 9.102236] usbcore: registered new interface driver rndis_host
[ 9.120953] rtl8192cu: Chip version 0x11
[ 9.207462] rtl8192cu: MAC address: 0c:82:68:23:17:4c
[ 9.212566] rtl8192cu: Board Type 0
[ 9.216315] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
[ 9.222291] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin
[ 9.231879] usbcore: registered new interface driver rtl8192cu
# 查询网络设备发现wlan0, 但未使能
root@BananaPi:/# ifconfig
eth0 Link encap:Ethernet HWaddr 02:88:07:C1:62:AA
inet6 addr: fe80::88:7ff:fec1:62aa/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:1087 (1.0 KiB)
Interrupt:117
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:96 errors:0 dropped:0 overruns:0 frame:0
TX packets:96 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:7416 (7.2 KiB) TX bytes:7416 (7.2 KiB)
root@BananaPi:/# ifconfig -a
eth0 Link encap:Ethernet HWaddr 02:88:07:C1:62:AA
inet6 addr: fe80::88:7ff:fec1:62aa/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:1087 (1.0 KiB)
Interrupt:117
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:104 errors:0 dropped:0 overruns:0 frame:0
TX packets:104 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:7824 (7.6 KiB) TX bytes:7824 (7.6 KiB)
wlan0 Link encap:Ethernet HWaddr 0C:82:68:23:17:4C
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root@BananaPi:/# cat /etc/config/wireless
config wifi-device radio0
option type mac80211
option channel 11
option hwmode 11g
option path 'soc@01c00000/1c1c000.usb/usb2/2-1/2-1:1.0'
option htmode HT20
# REMOVE THIS LINE TO ENABLE WIFI:
option disabled 1
config wifi-iface
option device radio0
option network lan
option mode ap
option ssid OpenWrt-BPI
option encryption none
root@BananaPi:/#
# 配置/etc/config/wireless使能wifi AP, 同时/etc/config/network按照2.1重新配置并重启网络服务.
root@BananaPi:/# cat /etc/config/wireless # 已经使能wifi ap
config wifi-device radio0
option type mac80211
option channel 11
option hwmode 11g
option path 'soc@01c00000/1c1c000.usb/usb2/2-1/2-1:1.0'
option htmode HT20
# REMOVE THIS LINE TO ENABLE WIFI:
option disabled 0
config wifi-iface
option device radio0
option network lan
option mode ap
option ssid OpenWrt-BPI
option encryption none
root@BananaPi:/#
root@BananaPi:/# /etc/init.d/network restart # 重启网络服务
[ 991.330108] device eth0 left promiscuous mode
[ 991.334586] br-lan: port 1(eth0) entered disabled state
[ 991.348363] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
root@BananaPi:/# [ 993.284846] RX IPC Checksum Offload disabled
[ 993.289242] No MAC Management Counters available
[ 993.295211] device eth0 entered promiscuous mode
[ 993.301789] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 993.797445] rtl8192cu: MAC auto ON okay!
[ 993.834994] rtl8192cu: Tx queue select: 0x05
[ 994.300507] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 994.309464] device wlan0 entered promiscuous mode
[ 994.331242] br-lan: port 2(wlan0) entered forwarding state
[ 994.336911] br-lan: port 2(wlan0) entered forwarding state
[ 994.342812] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 994.358747] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 996.334702] br-lan: port 2(wlan0) entered forwarding state
root@BananaPi:/# ifconfig # 显示wlan0网络设备启动OK
br-lan Link encap:Ethernet HWaddr 02:88:07:C1:62:AA
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::88:7ff:fec1:62aa/64 Scope:Link
inet6 addr: fdd9:5fd:97ff::1/60 Scope:Global
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:9 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:1254 (1.2 KiB)
eth0 Link encap:Ethernet HWaddr 02:88:07:C1:62:AA
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:1087 (1.0 KiB)
Interrupt:117
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:3216 errors:0 dropped:0 overruns:0 frame:0
TX packets:3216 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:192648 (188.1 KiB) TX bytes:192648 (188.1 KiB)
wlan0 Link encap:Ethernet HWaddr 0C:82:68:23:17:4C
inet6 addr: fe80::e82:68ff:fe23:174c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:18 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:2432 (2.3 KiB)
root@BananaPi:/# cat /var/dhcp.leases # 手机连接wifi热点后
1456971789 34:23:ba:df:b6:ac 192.168.1.246 android-xxx 01:34:23:bac
root@BananaPi:/# cat /proc/net/arp
IP address HW type Flags HW address Mask Device
192.168.1.246 0x1 0x2 34:23:ba:df:b6:ac * br-lan
|
最后, 大功告成, show一下.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 | root@BananaPi:/# cat /proc/net/arp
IP address HW type Flags HW address Mask Device
192.168.1.188 0x1 0x2 00:ea:01:17:97:ec * br-lan # RJ45连接PC(LAN)
192.168.42.129 0x1 0x2 16:16:89:51:07:d3 * usb0 # USB连接安卓手机并开启USB共享上网(WAN)
192.168.1.246 0x1 0x2 34:23:ba:df:b6:ac * br-lan # wifi连接手机(LAN)
root@BananaPi:/# ifconfig
br-lan Link encap:Ethernet HWaddr 02:88:07:C1:62:AA
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::88:7ff:fec1:62aa/64 Scope:Link
inet6 addr: fdd9:5fd:97ff::1/60 Scope:Global
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:22077 errors:0 dropped:0 overruns:0 frame:0
TX packets:2109 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1539394 (1.4 MiB) TX bytes:708324 (691.7 KiB)
eth0 Link encap:Ethernet HWaddr 02:88:07:C1:62:AA
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2127 errors:0 dropped:0 overruns:0 frame:0
TX packets:1945 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:255020 (249.0 KiB) TX bytes:689627 (673.4 KiB)
Interrupt:117
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:121 errors:0 dropped:0 overruns:0 frame:0
TX packets:121 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:9842 (9.6 KiB) TX bytes:9842 (9.6 KiB)
usb0 Link encap:Ethernet HWaddr 02:01:67:31:62:36
inet addr:192.168.42.220 Bcast:192.168.42.255 Mask:255.255.255.0
inet6 addr: fe80::1:67ff:fe31:6236/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:435 errors:1 dropped:0 overruns:0 frame:1
TX packets:20037 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:78807 (76.9 KiB) TX bytes:2507416 (2.3 MiB)
wlan0 Link encap:Ethernet HWaddr 0C:82:68:23:17:4C
inet6 addr: fe80::e82:68ff:fe23:174c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:20024 errors:0 dropped:0 overruns:0 frame:0
TX packets:343 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1601549 (1.5 MiB) TX bytes:45959 (44.8 KiB)
root@BananaPi:/#
|
WEB界面
固件分享, 送给有需要的朋友
1 2 3 | 版本: v1.0.1 固件: openwrt-sunxi-BPI-M1-sdcard-vfat-ext4.img-v1.0.1 链接: http://pan.baidu.com/s/1hra7CQo 密码: 5j23 |